0 Damage to various tv

By Unknown | At 08.42 | Label : Televisi | 0 Comments

Kerusakan2 Tv. (Sec. 13)
1. GOLDSTAR-CA14A62
Pictures of thin, PIF dganti remains: Checks Z201 (CF5, 5MHz).
* Test: Touch Base Q202, Nice pictures.
2. SHARP-51R200
Start to live and die, so Led Red: Check R502 For Supply Vertical.
2. FUJI ELECTRIC 29 "(TA8659)
Matrix Red color do not come out garbled (IC, Vcc ok): Check R729 (8k2) at Pin 2.
3. Sukira-CE1493
Standby B + ok, distart drop: Check D606.
4. TOSHIBA-2545DE (TA8808)
Regulators & Relay is not stable (Pump Up): Check Hor.Osc Out, Replace Crystal with 500F2 503F30 usual.
5. GOLDSTAR-CF14D20 (There SECAM)
Pictures sometimes color, sometimes not: Open R73 in Q07 Base.
6. DIGITEC-DT2082S
Pump Up & Regulators can not Adjust: Check Pin 3-14 TDA8380 (+ / - 10k), if
Too low / Short compensation.
7. DIGITEC-DM143031
V.Hold not function (IC, Vcc ok): Check C302, 303 (47u25v NP) in line CVBS / AV.
8. AKIRA-CT21PF9
Can not AV, Logic Control & 4053 ok: Check Pin 42 LA76810.
9. DIGITEC-DM143030
Blanking: Check T712 (BC547) on track H.Sync.
10. DIGITEC-DM143031
Over to 250V B +: Check R510 (1k) on the Regulator.
Kerusakan2 Tv. (Sec. 12)
1. POLYTRON-P in P
Tuning slide & Blanking, OSD ok: Checks Tuner (Digital 5v) damaged one.
2. FUJI ELECTRIC 21 "(TA7680)
Tuning slide, the search does not stop: Check Capacitor on PIF (68pf).
3. Dazz-145 038
Blanking & no black garis2, Sound ok No OSD: Check Elco Filter 180v.
4. -THOMSON TS4225
Deflection (Vertical) Protect installed, removed ok: Checks two series resistors (1.5 Mega) eastbound Toll Vertical.
5. POLYTRON (Reguator TDA8380)
Pump Up + B: Raise Filter Regulator 15V in Bag.Primer so 2200u
6. CHINESE MACHINERY
Regulators silent even without load: Check Capacitor on Power Base (15N).
7. JVC-AV.G201
Figure Hor. Drag & belang2 Black / White 10cm: Check C550 (100u16v) at Input 7805.
8. GOLDSTAR-CF14D20 (There ICs SECAM)
Led Distart flame and die (Not Standby): Check Pin 9 S6707, when Pump Up Check FR813 (1ohm), ZD803 (9V1).
9. MITSUNO (LA7688)
Start Sometimes, sometimes Standby: Replace the Eprom should 93LC56, 93C56 if you can not.
10. PANASONIC-TC2088
Regulator off: Check Q801 (C5253/C4804), Q805 (A1512/A733).
Kerusakan2 Tv. (Sec. 11)
1. SHARP-20U200
Grodok2 sound, picture ok: Sound System locked at D / K and can not be replaced, Replace & Adjust Eprom 24C08.
2. SHARP-14R20MKII
Start Green Led live and die so do not blink red (Hor.Osc ok): Checks Transformer Driver Hor.
3. POLYTRON-GM1492
Manual Tune does not stop: Replace transformer with E08L AFT.
4. SABA-MF5222
Blanking, Sound ok: Check AV Switch TEA2014
* Test: Jumper pin Socket Module 10-13 in AV
5. TOSHIBA-20N3XE (Bomba)
No Colour, Picture ok: Replace IC TB1231.
6. Sukira-CE1493
Vertical opening 8cm Just dtengah2: Check Voltage Pin 42 (TDA8361) of 33V.
7. GRUNDIG T22-3229
Panel does not function, OSD ok: Change R140 (820k) concentrated in 470K on Base TR107.
8. POLYTRON (AN5435-TDA3565)
Vertical can not be silent, not V.High Adjust Maximum: AN5435 & Replace R127 (13k)
9. SABA-MT5253
Protect, dstart live and die (9v ok): Check vertical IC TDA1771
* Test: Open Pin 9, Start ok.
10. TOSHIBA-1450XNE (Dramatic Vision)
Regulator Pump Up (No Load): Check D872 (Zener 16v) ​​on Regulator.
Kerusakan2 Tv. (Sec. 10)
1. SANYO-CG20SR1G (Galaxy)
Blanking: Check Eprom (A81DC-P307), Replace with 24C08 okay.
2. FUJITEC-FTC1499
Phase Hor. slide to right 15cm: Check Transformer Driver Hor.
3. SABA-MF5222
Tuning slide (stay tuned VIF): Replace LA7550 with LA7555 ok.
4. SONY-KV.G14B1
Protect, distart live and die: Check C623 (220u50v).
5. SOLITRON (Program CTV222S-PRC1.1)
Can flame, all the Panel does not function: Check Voltage Reset pin 33 (5v).
6. ADVANCE
Tuning slide: Check & Replace with E08L (Capacitor 68pf)
Adjust AGC (in Menu Service): 15.
7. AIWA-C143/203
Picture Red: Replace Eprom & Adjust RGB (White Balance).
8. GOLDSTAR-CBS4821
a. No Colour, if there is a color IC Delay puanas: Relpace MC144111
Test: Open Pin 4 = must be color
b. Preset panel does not function: Open Pin 6 ...
9. DIGITEC-DM1452
a. Blanking: Check T202, T205, T305
b. Bright, Contrass mblobor: Check T808
c. Channel Frequency until the middle of nothing: Check C102 (22N)
10. SONY-KV1430E
Vertical defects (Middle picture there is a white line 2cm): Check C854 (220u25v) Filter 12v
Kerusakan2 Tv. (Sec. 9)
1. POLYTRON-BB1475
Seolah2 Tuning slide, VIF 0k, there continues to be tension in BI: Check TR Band Switch T708 (BC548).
2. DIGITEC-DM1740
a. Auto Program is written directly UHF and AV1, AV2: 93C46 Eprom Replace original reply.
b. AV No, there are 15 TDA8361 Pin 8v, 3.5 v sharusnya: Replace TDA8361.
3. DIGITEC-DM172020
B + over and could not Adjust: Check TR Driver Regulator (C3807).
4. SHARP-14S20B/14R/B
No OSD, Picture slide to right 10cm: Check path AFC Pin 5 FBT.
5. DIGITEC-DM1452GB (Super Ninja)
Colors sometimes there, sometimes not: Replace Elco Filter B + (4.7 u160v).
* NB: Test, Try Parallel R R513 10k on pin 21 TA8690.
6. SAMSUNG-CB3862X
Picture opening dtengah 5cm, IC Vertical ok: Replace Elco 1000u35v Verticcal out.
7. Aetna-C1420
a. Vertical upper stretch, under less than 4cm (lain2 ok): Replace Eprom 24C04.
b. Auto Tuning ok, Figure ugly snoring sounds (Vcc ok): Checks SAW Filter.
8. HITACHI-CPT2451
Y (Luminance) No, Chroma (color image is ok): Checks Diode series TR Video Out Pin 24 LA7680.
9. SHARP-20A2-S
Picture Blooming (Mblobor), Colour ok: Recheck Service Parameter Adjustment.
10. NATIONAL-TC1475
Tuning slide (IC, IF, Tuner, Vcc ok): Check C1131 (0.33 u50v), C1132 (0.47 u50v) in a series of VT
Kerusakan2 Tv. (Sec. 8)
1. GOLDSTAR-CF14A170D
No Sound (Audio IC, LA7555 ok): Checks L201 (SIF 6.0 Mhz) Capacitor damaged (82pf).
2. PANASONIC (AN5601)
No Colour, Fine Tuning in there: Checks Trans Delay amplifier (C1685), Nb; Not Delay Line.
3. AKARI-IC14M88R (Sakura)
Pump Up Regulator (Without Load), kadang2 Standby: 6V2 Zener Check in VR Leaky B +.
4. PANASONIC-TC2088
Bright, Contrass, Colour is not the function (OSD ok): Checks R ABL (36K).
5. TOSHIBA-2955DE
Auto Search is ok, not the color Picture, Sound snoring: Check & Adjust Module L671 in SIF.
6. INTEL-IC2053RM
Picture ok, no brhenti Manual Tuning, VIF dganti remains: Replace LA7555.
Nb: Eprom 93C46N, If you can not wear 93C46P Memory.
7. Yoriko-YK2103ET
Vertical megap2, Vcc ok: Check Input 7812 (Not to be in less than 15V).
8. FUJI ELECTRIC 25 "(Video Master Stereo)
Picture No Syncron: Jumper Pin 1-3 at CN203 (teletex) with R 100ohm.
9. SABA-MF3702
No Colour, Picture ok: Check the LC 02 (Pin 36 M52038), Capacitor 47pf.
10. PANASONIC-TC1613R
Seolah2 Tuning slide / No Syncron, Sound ok: Check R125 (3k3), Replace with 1K2.
Kerusakan2 Tv. (Sec. 7th)
1. AKARI-IC14M88R
Regulator silence: Checks + Transistor Optocoupler.
2. POLYTRON-PN20123K (Stereo)
Protect, at the start of life and death (Vcc 0ke): Replace IC 4558 near the vertical amplifier.
3. JOHNSONS (FY 7698)
Chroma, color mblobor: Check Elco1u50v at Pin 6.
4. POLYTRON-GM1490 (TDA2579)
Phase Hor. Slide (no black line) almost to the middle: Check R449 (68k) to Pin 12.
5. AKARI-IC1437RMD
Regulator silent: Check ZD812 (18V), C815 (100u25v), C820 (1u100v).
6. TELESONIC-TC5191GR
Power On, Relay On (supposedly silent Standby): Check C120 (22u50v) at Base TR113.
7. SAMSUNG-CB3366Z (Bio)
a. SMR 40 000 damaged, replaced broken again: Replace the first module drivers (HIS 0169).
b. Auto Program could Memory, Adjust V, H, RGB is not: Replace Eprom 24C04.
8. Dazz-DZ2570A
Not Start: Check Hor.Vcc, must be 8volt.
9. DAEWOO-DMQ2044
No OSD, Panel Normal function: Replace IC Program (M34300M4-230SP).
10. POLYTRON-LFS1465
Led Channel flame all, not Preset function: Ceeek R18 (10k) at Pin 19 (UPC 1363).
Kerusakan2 Tv. (Sec. 6)
1. FUJI ELECTRIC (TA8659, TA8403)
B + up to 300V; Check Elco10u STR58041 160v at pin 1.
2. BLAUPUNKT-CTV54158JK
Matrix chaotic (Can not PAL); Check R523 (10k) Disconnect!
3. SHARP-C1424AU
a. Increased to 250V B + (R, Elco, Diode, TR, Vcc okay); Replace STR41090
b. Regulators silent; Check TR3279, D706, R705, 6.7
4. PANASONIC-TC2088DX (Stereo)
Picture ok, Contrass not function, sometimes Veretical (line); Cheque R ABL (37K).
5. POLYTRON-PN14123KAG
Can not start, Vcc okay (Osciator Hor. No.); Repace TDA8841.
6. SONY-KV G14P1 (AV Remote)
Dark screen, OSD there; Check ABL, R857 (82K)
7. SONY-KV1415GE
At the start TR Hor. Puanas; Check Hor.Osc Pin 27 and Replace CXA1213BS.
8. AIWA-A205KER
a. No OSD (Vcc, Crystal okay); Replace M37220M3-150SP.
b. OSD only Red colored; Replace TA8759BN.
c. Blanking; Check D302 Zener 12v (Chroma Vcc).
9. SOLITRON-SM5108
a. Tuning slide, VIF okay; Replace TDA 8222.
b. No Sound, Audio IC okay; Replace & Adjust SIF (102).
10. GOLDSTAR-SoundMAX
Blanking, RGB Vcc okay; Replace TA8690.
Kerusakan2 Tv. (Sec. 5)
1. Chancellor P191
No OSD (No Can Program); Check D102 (4148) near the IC Program.
2. MAYAKA-R14MC02
Vertical defects (garis2 black in the middle); Check C406 (220N) R416 series.
3. GRUNDIG p37-832
a. Picture a little Blanking, no sound Criiit; Check C803 (220u 25v), C806 (220u 50V).
b. Image edge runcing2; Check C925 (470u 25v) 12v Vcc filter.
4. SANYO C14C11U (14U)
Standby (can not start); Check R555 (47k).
5. PHILLIPS-14GR1024
a. Over Voltage Protect; Open D6638 and adjust VR, B + must be 97 volts.
b. Blanking Sound okay; Check & Replace TDA3653B
6. INTEL-IC2053RM/1461NW
a. No OSD; Open Zener on Vertical Socket.
b. VIF in tuning has not changed; Replace LA7555.
7. PHILLIPS-C14PT138J (Tvku dewe ...!)
Standby at the start protected; Check & Replace Vertical IC TDA3653B.
8. INTEL-IC1429N
Figure shrink both sides 3cm; Check C707 (100u 50V), D703 (1N5392).
9. PANASONIC-TC1450
a. Blanking & Protect; Replace AN5600.
b. No Sound; Check Q1112, 1113 (N4212) Replace with C114.
10. TOSHIBA-2840XH
Vertical defects (R, C, Elco, okay smua IC), check out Vertical Feedback drives = 3-4Volt.
Kerusakan2 Tv. (Sec. 4)
1. CONTEC KTB3731
Matrix (Color) chaotic, IC Video M51393 okay; Check R235 (8k2) broke!
2. NATIONAL (AN 5601)
At the start of life and die (Protect), Vcc okay; Check Q504 (Base must be 0 Volt)!
3. METZ 7401/3
Relay bissa on, B + no; Check R808 (2.2 Ohm ½ Watt), R821 (56 Ohm ¼ Watt)
4. LENS (KA2154, SMM105, KA2919)
Tuning okay, not memory; Check RR151 (150k) from AFT Tuner Pin 35 UCOM!
5. TAMASHI (TDA8362, SMP260WTC)
At the start Protect; Check TR Hor. Driver (C2482)?
6. SABA MF5222
a. Contrass not function, Voltage Swing okay; Check RL05 (100k) Pin 3-4 FBT!
b. Vertical defects above; Check CL15 (220u 16v).
c. Vertical mebuka 1cm below; Check CF06 (470n).
7. SABA MS3705
a. No OSD; Check R 68k in base amplifier RGB (Must be 4.8 volts)!
b. Blanking (No Snow); Cheque TR Video TV05 (BC558)?
8. SANSUI SV.M1460J
No sound, Voltage swing right; Replace TDA1013.
9. JVC C147LNS
Protect; Check M52016 and deflection.
10. DETRON / ETRON P1401
No Hor. Oscillator, Vcc okay; Replace TA 7698.
Kerusakan2 Tv. (Sec. 3)
1. OKAY 3732
Tv live, - / + 5 minutes off (Standby), Eeprom MN12C01 okay; Cheque Toll pathway
Validate (Ceramic 22N) leaked!
2. INDOTEC 2107
Vertical upper disability; Check R304 (56k) stretch!
3. AKAI CT14W9
a. Vertical does not open, AN5534 cold; Vertical Deflection part broke!
b. No snow, no OSD; 5v drop (5V1 Zener leak)!
4. DAEWOO DMQ1449M
Vertical defects, the top is white garis2; Replace LA7837!
5. Aetna C1420
a. Can not Standby (immediate start); Replace TMP87CK38N!
b. Blanking (Vcc okay); Replace TB1238AN!
c. Tuning slide, the sound of snoring (VIF does not function); Replace SAW Filter!
6. KONKA 1418C3
Pump up B +; Check Optic Coupler (PC817)!
7. RCA E14500 (SABA MT 3751)
a. B + Okay, Led Blink; Replace STV 2118!
b. No Sound Picture oke (Vcc TDA7253, Voltage Swing okay); Replace STV8224A!
c. Vertical up less 3cm; Adjust B +, must be 100V!
8. JOHNSONS CTV145AV
Standby can not start; Cheque Crystal IC Program!
9. CROWN T128
At the start snoring sound, either the account after 3 minutes (PIF okay); Replace Transformer SIF!
10. SEMRO TD1538
+ B can not be adjusted; Check R808 (10k) at the Regulator
Kerusakan2 Tv. (Sec. 2)
1. GOLDSTAR-C14D22
Stand By at the start protect LED flashing: Check Zener 6v8 in the bag. PSU.
If at the start led to death: Check SE110.
2. GOLDSTAR-CA14A95C
Manual tuning does not stop: Replace UCOM GS8334-02B.
3. SAMSUNG-CB3339Z
Blanking: Cheque supply 5v (7805).
4. SAMSUNG BIO-CB3366Z
Blanking (Vcc ok): Replace IC Chroma M52309SP.
5. SAMSUNG-CB2039Z
Tuning no channel (33V, VT okay): Checks 12v supply.
6. AIWA-C142KER
Vertical Line: Checks 12v supply.
7. SONY-KV1415GE
Tuning can not save channel: Replace UCOM M34302M8-712SP.
8. SOLYTRON-SM3725
Position AV voice channel remains: Check Q1006 to pin 12 IC 4053.
9. SOLYTRON-SM3792
Tuning can be stopped, but the channel is not trsimpan: Memory Check-30V supply.
10. SOLYTRON-SM3730
Sometimes it can start, sometimes die: Check 15V, C853 (4.7 u 50V NP).
Damage Tv. (Sec. 1)
1. DIGITEC DM-172 020
OSD not out: check T701, T712 (BC547).
BI-BIII okay, BU no: checks Band Switch LA7910.
2. DIGITEC DM-14 401
Tr.Hor dpasang B + drop: check C516 (1u50v).
3. DIGITEC-DM142014
Bright, Contrass not function: Checks T303 (BC557).
Horizontal not Syncron: Check T301 (BC548).
4. DIGITEC-DM2076
Contrass not function: open pin 25 TDA8361, TDA8361 Replace if ok.
5. DIGITEC-DM2142
Blue screen, No OSD: Replace TDA8361.
6. POLYTRON-GM1483
No OSD: open R723, D732.
7. AKARI-IC1439 R2N
No raster (Vcc ok): Check R411.
8. AKARI-IC1439RMD
B + drop, Heater no, Sound ok: Check C561, R443.
9. GOLDSTAR-SoundMAX
Color kadang2 missing: Check & Replace Ceramic pin 11 TDA8690.
10. GOLDSTAR-C14D22
No sound, no manual tuning stops: Check QO6 (C3198).

0 Broken Tv Froblems

By Unknown | At 08.35 | Label : tehnologi | 0 Comments

This is a series of television equipment. we know that television is very important in this era of all-powerful if we did not have television would not know news and news in other countries what we know of our own country if we damaged the TV must have been very disappointed and therefore sadly the writing of this article I will discuss eektronika electronics problem is the problem of damage bernacam-kind television I will present the tricks on this issue later wrote destruction awaited television is just beginning saja.sekian and thanks

1 TV AKARI blue beach

By Unknown | At 09.18 | Label : Televisi | 1 Comments

following data
00th
OSD contrast 60
bright sub 80
sub contrast 55
sub collor 63
sub tint 80
sub-sharp 50

01
127 red bias
160 green bias
blue bias 140
red drive 63
8 green drive
blue drive 63

02
V pos/50mhz 10
V pos/60mhz 20
Vsize/50mhz 58
Vsize/60mhz 90
VSC 18
Vlinearity 15
Vsize CMP 6

03
H freq 20
H phase/50mhz 10
H phase/60mhz 13
H blk L 2
R 5 H blk
blank def 0
coring enable 0

04th
collor sya 2
sif sys sw 5.5
C ext 0
C bypass 0
C kill on 0
C kill off 0

05th
syn kill 0
RF AGC delay 18
V kill 0
cross B / W 0
fm level 12
video level 6

06th
digital OSD 0
audio sw 0
video sw 0
AKB def 1
auto fresh 0
count down mod 0
gray mode 0
vsync sep up 0

07th
killer sys 2
volume filter 0
Vif sys sw 38.9
brt abl def 1
brt abl treshold 0
brt stop mod def 0
emg abl def 1

08th
afc gain and gate 0
SECAM B-y dc 8
SECAM R-y dc 8
R-y/B-y gain bal 8
R-y/B-y angle 8
B gamma seleck 3
RG gamma def 0

09th
audio mute 0
fm mute 0
video mute 0
sound trap 4
fm gain 0
de emphasis tc 0
FBP blk sw 0

10th
disable 0
vertical test 0
tint test 0
collor test 1
test drive 0
contrast test 0
OSD contras test 0
IMR test 0

11th
OSD H position 12
1 opt sys collor
sif opt sys 0
no opt bass

4 China TV Service Mode

By Unknown | At 09.11 | Label : Televisi | 4 Comments

TDA9384PS/N2/31FM-OSD (AKIRA)
Memory 24C08
Press CLOCK sequence, P.M, TIMER (DISP)
Press 0-9 to select MENU
TDA9350PS/N1/2K0172
TDA9350PS/N1/2K0223 TELRA TDA9350S2
TDA9380PS/N1/1L0231
TDA9353PS/N1/2I0269
TDA9350PS/N2/2I0851
TDA9350PS/N1/2L0296 TELRA W3A
TDA9353PS/N1/2L0297 TELRA_W3_A
TDA9350PS/N1/2S0296 TELRA W3A
TDA9350PS/N1/2S0510 TELRA_T3_A
TDA9353PS/N1/2S0511 TELRA_T3_A
TDA9350PS/N1/2S0512 TELRA_T3_D
TDA9350PS/N1/2S0546
TDA9353PS/N1/2S0596 TELRA_T3_E
TDA9353PS/N2/2I0869 TELTRA T4C
TDA9351PS/N2/2I0927 TELRA T4
TDA9353PS/N2/2I1186 TELRA_T5_E
TDA9351PS/N2/2I1192 TELRA_T5_W
TDA9353PS/N1/3S0342 TELRA W4 C
TDA9360PS/N1/4S0415 TELRA A2
TDA9360PS/N1/4S0430
• To enter the SERVICE mode press SUB PAGE button on the remote while press and on TV VOL. -
Chassis UOC-TDA9381 (C312)
• Press the MENU button and press the code 8500. In the upper left corner there is a symbol M.
• The number 0 ... 9 to choose the desired MENU

NTDA9381C38ND NOM8370-B-16NB
NTDA93412NC
• Press MENU - display image menu and enter the code 6 4 8 3 - display M.
• To exit the factory mode and return to normal STBY push one time.
• In the factory mode {"M" mode) there are ten full menu. Menu 1 Menu 4 can be selected directly but menu 5 Menu 0 should choose measures: CALL press, to call the "M", press LOCK, then press any of the numeric keys 5-0.
• For example, to select Menu 7, you must press the CALL and turns LOCK, then press 7.
Chassis UOC-TDA9384
• Press CALL, PRESS MUTE and 980 codes. In the upper left corner there is a symbol M.
Chassis HAIER
TDA9370PS/N2/AI0961
24C08
• Press the QV hold about 4 seconds and then press the button on the RC Menu1.
• Press the TEST button on the RC unit for factory use.
The "TEST" is displayed on the screen. Digital Press, (Mkey) and corresponding display on the screen will appear.
Some time "PASSWORD" will appear on the screen, you need to enter 828.

LC86332A-51C7
• 1. Tap holes that are already available on the remote
• 2. Press MENU 8 6 3 3.
LC86332B - 52Z6, 53L1
• 1. Tap holes that are already available on the remote
• 2. Press MENU or 8 6 3 3 6 4 8 3.
LC863532A-57P1-57Z0
Two ways to enter service mode
• 1.Press hidden buttons located above the GAME. If the hidden button is missing, by opening the control panel, find cover two contacts that led to Menu SERVICE. Standard matrix, 8x4, usually entered BUS press P + P-STBY and 9.5, Sleep
• 2. Clicking the MENU button three times to enter the Settings page. Press P + or P-select SWITCHING line. Dial code "2483." TV in the MENU PAGE. Turn the page menu button press MUTE PAGE, Disable Vertical - TV / AV. To enter the service menu of 3 or higher, you have to set PAGE OPTION 1.
LC863328A 5W63, 52E5, 56C9 / LC863320A-5R76
• Press RECALL once, press VOL-on the panel while hold press RECALL

Chassis 502 LC863532 - 54D5, 54H7, 5Z00, 50S8, 50S9, 52Y7
Two ways to enter service mode
• 1. Plug in the supplied remote hole
• 2.Atur volume 0, press MENU 6 5 6 8.
Chassis 3Y11/3Y01/4Y01 LC863324A-5S68
• 2X MENU RECALL, QVIEW, MUTE
UСom ST6-ELAME2
• Click the button: SKIP, VOL-, FINE TUNE
Chassis 3S10 ST92185BN4B1/PBI - 3S10B-ENG/RUSS W / O
There are two ways to enter the service mode:
• 1) Press the hidden and located right next to the MENU button
• 2) Press and hold the MENU button on the order of AV ANAL
Pressing OK will enter the selection.
For IAC 2000 code: 1124, with MENU = MENU, AV = AV, ANAL + B = CHIFT, OK = MUTE, PP = CHIFT + OK.
To exit the service menu you have to click away from the TV or PP.

Chassis PT90
ST92195C7B1/MIF
ST92195C7B1/PFT
• Turn on your TV.
• Select the FEATURES MENU.
• Dial code 1923
TMP87CM38N-2A55,-3GG3
• Adjust volume = 0, press VOL-on TV and hold it while pressing the CALL / disply. The screen will display the symbol D. It is a simple service S mode, which is available to the service mode from the menu 0, 1 and 2. To enter the service mode extended to S mode, press SYSTEM. The screen will display the symbol D.
MCL437F, TMP87CK38N-1A72
• Press the MUTE button on the remote control is released, press MUTE again and hold her press MENU on the TV.
• The screen will display the symbol D. It is a simple service mode S. To enter the service mode extended to S mode, repeat the operation. The screen will display the symbol D.
TMP87PS38N-M13VR2V1
• Press VOL - to 0 and hold the TV while press DISPLAY on the remote.
• The screen will display the symbol D. It is a simple service mode S. To enter the service mode extended to S mode, repeat the operation. The screen will display the symbol D.
• The transition between the two groups through the DISPLAY menu. The selection of options and make the determination P +, P-, V + and V-.
TMP87CM38N-3GN5, TMP87CK38N-2B46, Chassis TB1238
To get into the service mode via the following procedure:
• Press for the introduction of two-digit channel number and program -/-- 12.
• After the transition, select program 38.
• Channel 38 MENU button a second menu with POS.LOCK
• Press MUTE. The first sign that everything is done properly there will be no indication of muting.
• Enter the password 1 2 3 8. TV will go into service mode and the display shows M. symbol

(The latest model of entry into the service mode for some versions of the processor has been simplified to a standard for Changhong - at zero volume.)

CHANGHONG
Chassis CN-12C1, [CN-ER]
CH04T1221-50L9 (CH04T1222, CH04T1228)
• Set the volume level of 0.
• Press MUTE on the remote control, hold, click VIDEO TV.
• Set the TV to the SELECT MENU button on the remote control.
• Press the (ME) on the remote control to exit the service mode.
TCL
• Vol 0 Press and hold Vol - on TV while press Disply in Remote
TCL Chassis M11 (M37221M4-322SP)
• The panel should simultaneously pressing the DISPLAY button and VSM.
• USE menu buttons (up, down, left and right) to adjust the settings menu of services.
• Press DISPLAY to save the settings and exit the Service mode.
Chassis 5N11
STV5348/T-A5 S3C8849X15-AQB7 (S3P8849XZZ-AQB9)
24C08
IC Video: NN5198 (NN5099)
• Position standby press and hold VOL + VOL-on the TV panel
CHINA WITH SERVICE MODE SANYO LC863xxx
Sometimes we come across an obscure Chinese TV brands her. To open the service mode following methods may be tried (we mostly there has been the practice)
LC863324A-5T51
• Go to the menu Auto-Program/Auto-Search
• Then press the sequence 6-4-8-3 to enter the service menu.
• Press the 6-4-8-3 sequence again to enter the factory mode.
 
LC863524C-55L7
• Vol minimal
• Press and hold down the VOL-panel TVs
• Press and hold on the remote REVIEW
• Move-made menu MUTE
 
LC863528A-xxxx
• Press and hold down the VOL-panel TVs
• Tap Review
• Repeat to exit
 
LC863328A-5Y29/-5Y28/-5Y19
• Vol minimal
• Press and hold down the Vol-panel TVs
• Press 0 diremot 3 times.
 
LA863328A-5028/-2MD0/-C81DC
• Find an empty button on the remote is not in use.
 
LC863528B-52K7
• Volume minimal
• Press the MENU-2 to select EXCHANGE PROGRAM (move program)
• Enter the numbers 2-4-8-3
• Move-made Quick-View menu.
 
LC863528B-51C3
• Press DISPLAY
• Press MUTE 3x
• Move menu with SLEEP
• Press MENU to save / exit.
 
LC8633528B-50S8
• Go to the menu Auto-Program/Auto-Search
• Then press the sequence 6-4-8-3
• Press the 6-4-8-3 sequence again to enter the factory mode.
 
LC863532A-5Z00
• Vol minimal
• Press and hold down VOL-paneled TV
• Press DISPLAY diremot
• Press POWER on the remote to save / exit.
 
LC863332B-52Z6/-3KD0/-53L1/-54R6, LC863532C-55P9/-55K9
• Vol minimal
• Tekan2 MENU to select the PICTURE menu (PICTURE MENU)
• Press 8-6-0-0, or 8 March 6, or 6-4-8-3
 
LC863320A, LC863324A, LC863328A, LC863332B
• Press the hidden button on the remote. Usually under the SLEEP button.
• Or can pin ic remote menshort 2-13 or 2-14, or 2-15, or 2-16
 
LC863532B-52H8
• Press the Menu
• Press the 8-8-8 sequence.
 
LC863532B-55L1
• Volume minimal
• Press the MENU
• Press the sequence 6-5-6-8
• Moving the Display menu use.
 
LC863332B
• Turn on the TV remote dg
• Press sequential "POWER", "MUTE", "CALL", "TIMER," until it says "FACTORY"
• Press the "TIMER"
 
LC863548B
• Vol minimal
• Press and hold down the VOL-panel TVs
• Press DISPLAY diremote
CHINA SERVICE MODE UOC TOSHIBA TMPA88xx
Sometimes we come across an obscure Chinese TV brands her. To open the service mode following methods may be tried (we mostly there has been the practice)
 
TMPA-6F53 8873CPANG
• Vol minimal
• Press and hold the VOL-down on panel tv,
• Then press the DISPLAY button on the remote
• Will display the letter "S" in upper right corner,
• Repeat these steps until the letter "D" on the top right corner of the screen
• Press the MENU button on the remote or on the TV panel to enter the MENU MENU 0 to 11 as well as setting the B / W BALANCE.
• To SAVE / EXIT / EXIT the service mode turn off the tv.
 
TMPA-8873CSCNG 6PR6.
• Vol minimal
• Press and hold down the Vol-panel TVs
• Then press the DISPLAY button on the remote, until the word "FACTORY"
• Press the DISPLAY button 1x to enter the B / W setting
• Press DISPLAY 1 time again to get into the setting F1 or:-press the number 0 to enter the B / W-press the number 1 to get into F1-press button number 2 to get into F2-press the number 3 to get into F3-press the number 4 to enter the F4-press the number 5 to get into F5-press the number 6 to get into F6-press the number 7 F7 to enter 4.
• To save / SAVE / exit / EXIT DISPLAY button on the remote.
 
TMPA-8800CPN-3GV1 244KJ
• Vol minimal
• Press and hold down the Vol-panel TVs
• Then press the CALL will display mode S. there is a few settings.
• Then press Vol-down and hold
• Press the CALL button on the remote again will display the menu D
• Press MENU to select the option
 
TMPA-8851CPNG-6EG1
• Vol minimal
• Press and hold down the VOL-panel TVs
• Press DISPLAY diremote
 
TMPA8821CPNG-4UD4
• Press the 30 channel
• Press the 88 channel
• Press VOL-down
• Press MUTE.
 
TMPA8891CSCNG6V12
• Set the TV Vol minimum
• Press and hold the Vol-down on a flat panel and press the DISP button on the remote.
• or Press MENU, CH-down and enter code 2483 or 6483.