Kerusakan2 Tv. (Sec. 13)
1. GOLDSTAR-CA14A62
Pictures of thin, PIF dganti remains: Checks Z201 (CF5, 5MHz).
* Test: Touch Base Q202, Nice pictures.
2. SHARP-51R200
Start to live and die, so Led Red: Check R502 For Supply Vertical.
2. FUJI ELECTRIC 29 "(TA8659)
Matrix Red color do not come out garbled (IC, Vcc ok): Check R729 (8k2) at Pin 2.
3. Sukira-CE1493
Standby B + ok, distart drop: Check D606.
4. TOSHIBA-2545DE (TA8808)
Regulators & Relay is not stable (Pump Up): Check Hor.Osc Out, Replace Crystal with 500F2 503F30 usual.
5. GOLDSTAR-CF14D20 (There SECAM)
Pictures sometimes color, sometimes not: Open R73 in Q07 Base.
6. DIGITEC-DT2082S
Pump Up & Regulators can not Adjust: Check Pin 3-14 TDA8380 (+ / - 10k), if
Too low / Short compensation.
7. DIGITEC-DM143031
V.Hold not function (IC, Vcc ok): Check C302, 303 (47u25v NP) in line CVBS / AV.
8. AKIRA-CT21PF9
Can not AV, Logic Control & 4053 ok: Check Pin 42 LA76810.
9. DIGITEC-DM143030
Blanking: Check T712 (BC547) on track H.Sync.
10. DIGITEC-DM143031
Over to 250V B +: Check R510 (1k) on the Regulator.
Kerusakan2 Tv. (Sec. 12)
1. POLYTRON-P in P
Tuning slide & Blanking, OSD ok: Checks Tuner (Digital 5v) damaged one.
2. FUJI ELECTRIC 21 "(TA7680)
Tuning slide, the search does not stop: Check Capacitor on PIF (68pf).
3. Dazz-145 038
Blanking & no black garis2, Sound ok No OSD: Check Elco Filter 180v.
4. -THOMSON TS4225
Deflection (Vertical) Protect installed, removed ok: Checks two series resistors (1.5 Mega) eastbound Toll Vertical.
5. POLYTRON (Reguator TDA8380)
Pump Up + B: Raise Filter Regulator 15V in Bag.Primer so 2200u
6. CHINESE MACHINERY
Regulators silent even without load: Check Capacitor on Power Base (15N).
7. JVC-AV.G201
Figure Hor. Drag & belang2 Black / White 10cm: Check C550 (100u16v) at Input 7805.
8. GOLDSTAR-CF14D20 (There ICs SECAM)
Led Distart flame and die (Not Standby): Check Pin 9 S6707, when Pump Up Check FR813 (1ohm), ZD803 (9V1).
9. MITSUNO (LA7688)
Start Sometimes, sometimes Standby: Replace the Eprom should 93LC56, 93C56 if you can not.
10. PANASONIC-TC2088
Regulator off: Check Q801 (C5253/C4804), Q805 (A1512/A733).
Kerusakan2 Tv. (Sec. 11)
1. SHARP-20U200
Grodok2 sound, picture ok: Sound System locked at D / K and can not be replaced, Replace & Adjust Eprom 24C08.
2. SHARP-14R20MKII
Start Green Led live and die so do not blink red (Hor.Osc ok): Checks Transformer Driver Hor.
3. POLYTRON-GM1492
Manual Tune does not stop: Replace transformer with E08L AFT.
4. SABA-MF5222
Blanking, Sound ok: Check AV Switch TEA2014
* Test: Jumper pin Socket Module 10-13 in AV
5. TOSHIBA-20N3XE (Bomba)
No Colour, Picture ok: Replace IC TB1231.
6. Sukira-CE1493
Vertical opening 8cm Just dtengah2: Check Voltage Pin 42 (TDA8361) of 33V.
7. GRUNDIG T22-3229
Panel does not function, OSD ok: Change R140 (820k) concentrated in 470K on Base TR107.
8. POLYTRON (AN5435-TDA3565)
Vertical can not be silent, not V.High Adjust Maximum: AN5435 & Replace R127 (13k)
9. SABA-MT5253
Protect, dstart live and die (9v ok): Check vertical IC TDA1771
* Test: Open Pin 9, Start ok.
10. TOSHIBA-1450XNE (Dramatic Vision)
Regulator Pump Up (No Load): Check D872 (Zener 16v) on Regulator.
Kerusakan2 Tv. (Sec. 10)
1. SANYO-CG20SR1G (Galaxy)
Blanking: Check Eprom (A81DC-P307), Replace with 24C08 okay.
2. FUJITEC-FTC1499
Phase Hor. slide to right 15cm: Check Transformer Driver Hor.
3. SABA-MF5222
Tuning slide (stay tuned VIF): Replace LA7550 with LA7555 ok.
4. SONY-KV.G14B1
Protect, distart live and die: Check C623 (220u50v).
5. SOLITRON (Program CTV222S-PRC1.1)
Can flame, all the Panel does not function: Check Voltage Reset pin 33 (5v).
6. ADVANCE
Tuning slide: Check & Replace with E08L (Capacitor 68pf)
Adjust AGC (in Menu Service): 15.
7. AIWA-C143/203
Picture Red: Replace Eprom & Adjust RGB (White Balance).
8. GOLDSTAR-CBS4821
a. No Colour, if there is a color IC Delay puanas: Relpace MC144111
Test: Open Pin 4 = must be color
b. Preset panel does not function: Open Pin 6 ...
9. DIGITEC-DM1452
a. Blanking: Check T202, T205, T305
b. Bright, Contrass mblobor: Check T808
c. Channel Frequency until the middle of nothing: Check C102 (22N)
10. SONY-KV1430E
Vertical defects (Middle picture there is a white line 2cm): Check C854 (220u25v) Filter 12v
Kerusakan2 Tv. (Sec. 9)
1. POLYTRON-BB1475
Seolah2 Tuning slide, VIF 0k, there continues to be tension in BI: Check TR Band Switch T708 (BC548).
2. DIGITEC-DM1740
a. Auto Program is written directly UHF and AV1, AV2: 93C46 Eprom Replace original reply.
b. AV No, there are 15 TDA8361 Pin 8v, 3.5 v sharusnya: Replace TDA8361.
3. DIGITEC-DM172020
B + over and could not Adjust: Check TR Driver Regulator (C3807).
4. SHARP-14S20B/14R/B
No OSD, Picture slide to right 10cm: Check path AFC Pin 5 FBT.
5. DIGITEC-DM1452GB (Super Ninja)
Colors sometimes there, sometimes not: Replace Elco Filter B + (4.7 u160v).
* NB: Test, Try Parallel R R513 10k on pin 21 TA8690.
6. SAMSUNG-CB3862X
Picture opening dtengah 5cm, IC Vertical ok: Replace Elco 1000u35v Verticcal out.
7. Aetna-C1420
a. Vertical upper stretch, under less than 4cm (lain2 ok): Replace Eprom 24C04.
b. Auto Tuning ok, Figure ugly snoring sounds (Vcc ok): Checks SAW Filter.
8. HITACHI-CPT2451
Y (Luminance) No, Chroma (color image is ok): Checks Diode series TR Video Out Pin 24 LA7680.
9. SHARP-20A2-S
Picture Blooming (Mblobor), Colour ok: Recheck Service Parameter Adjustment.
10. NATIONAL-TC1475
Tuning slide (IC, IF, Tuner, Vcc ok): Check C1131 (0.33 u50v), C1132 (0.47 u50v) in a series of VT
Kerusakan2 Tv. (Sec. 8)
1. GOLDSTAR-CF14A170D
No Sound (Audio IC, LA7555 ok): Checks L201 (SIF 6.0 Mhz) Capacitor damaged (82pf).
2. PANASONIC (AN5601)
No Colour, Fine Tuning in there: Checks Trans Delay amplifier (C1685), Nb; Not Delay Line.
3. AKARI-IC14M88R (Sakura)
Pump Up Regulator (Without Load), kadang2 Standby: 6V2 Zener Check in VR Leaky B +.
4. PANASONIC-TC2088
Bright, Contrass, Colour is not the function (OSD ok): Checks R ABL (36K).
5. TOSHIBA-2955DE
Auto Search is ok, not the color Picture, Sound snoring: Check & Adjust Module L671 in SIF.
6. INTEL-IC2053RM
Picture ok, no brhenti Manual Tuning, VIF dganti remains: Replace LA7555.
Nb: Eprom 93C46N, If you can not wear 93C46P Memory.
7. Yoriko-YK2103ET
Vertical megap2, Vcc ok: Check Input 7812 (Not to be in less than 15V).
8. FUJI ELECTRIC 25 "(Video Master Stereo)
Picture No Syncron: Jumper Pin 1-3 at CN203 (teletex) with R 100ohm.
9. SABA-MF3702
No Colour, Picture ok: Check the LC 02 (Pin 36 M52038), Capacitor 47pf.
10. PANASONIC-TC1613R
Seolah2 Tuning slide / No Syncron, Sound ok: Check R125 (3k3), Replace with 1K2.
Kerusakan2 Tv. (Sec. 7th)
1. AKARI-IC14M88R
Regulator silence: Checks + Transistor Optocoupler.
2. POLYTRON-PN20123K (Stereo)
Protect, at the start of life and death (Vcc 0ke): Replace IC 4558 near the vertical amplifier.
3. JOHNSONS (FY 7698)
Chroma, color mblobor: Check Elco1u50v at Pin 6.
4. POLYTRON-GM1490 (TDA2579)
Phase Hor. Slide (no black line) almost to the middle: Check R449 (68k) to Pin 12.
5. AKARI-IC1437RMD
Regulator silent: Check ZD812 (18V), C815 (100u25v), C820 (1u100v).
6. TELESONIC-TC5191GR
Power On, Relay On (supposedly silent Standby): Check C120 (22u50v) at Base TR113.
7. SAMSUNG-CB3366Z (Bio)
a. SMR 40 000 damaged, replaced broken again: Replace the first module drivers (HIS 0169).
b. Auto Program could Memory, Adjust V, H, RGB is not: Replace Eprom 24C04.
8. Dazz-DZ2570A
Not Start: Check Hor.Vcc, must be 8volt.
9. DAEWOO-DMQ2044
No OSD, Panel Normal function: Replace IC Program (M34300M4-230SP).
10. POLYTRON-LFS1465
Led Channel flame all, not Preset function: Ceeek R18 (10k) at Pin 19 (UPC 1363).
Kerusakan2 Tv. (Sec. 6)
1. FUJI ELECTRIC (TA8659, TA8403)
B + up to 300V; Check Elco10u STR58041 160v at pin 1.
2. BLAUPUNKT-CTV54158JK
Matrix chaotic (Can not PAL); Check R523 (10k) Disconnect!
3. SHARP-C1424AU
a. Increased to 250V B + (R, Elco, Diode, TR, Vcc okay); Replace STR41090
b. Regulators silent; Check TR3279, D706, R705, 6.7
4. PANASONIC-TC2088DX (Stereo)
Picture ok, Contrass not function, sometimes Veretical (line); Cheque R ABL (37K).
5. POLYTRON-PN14123KAG
Can not start, Vcc okay (Osciator Hor. No.); Repace TDA8841.
6. SONY-KV G14P1 (AV Remote)
Dark screen, OSD there; Check ABL, R857 (82K)
7. SONY-KV1415GE
At the start TR Hor. Puanas; Check Hor.Osc Pin 27 and Replace CXA1213BS.
8. AIWA-A205KER
a. No OSD (Vcc, Crystal okay); Replace M37220M3-150SP.
b. OSD only Red colored; Replace TA8759BN.
c. Blanking; Check D302 Zener 12v (Chroma Vcc).
9. SOLITRON-SM5108
a. Tuning slide, VIF okay; Replace TDA 8222.
b. No Sound, Audio IC okay; Replace & Adjust SIF (102).
10. GOLDSTAR-SoundMAX
Blanking, RGB Vcc okay; Replace TA8690.
Kerusakan2 Tv. (Sec. 5)
1. Chancellor P191
No OSD (No Can Program); Check D102 (4148) near the IC Program.
2. MAYAKA-R14MC02
Vertical defects (garis2 black in the middle); Check C406 (220N) R416 series.
3. GRUNDIG p37-832
a. Picture a little Blanking, no sound Criiit; Check C803 (220u 25v), C806 (220u 50V).
b. Image edge runcing2; Check C925 (470u 25v) 12v Vcc filter.
4. SANYO C14C11U (14U)
Standby (can not start); Check R555 (47k).
5. PHILLIPS-14GR1024
a. Over Voltage Protect; Open D6638 and adjust VR, B + must be 97 volts.
b. Blanking Sound okay; Check & Replace TDA3653B
6. INTEL-IC2053RM/1461NW
a. No OSD; Open Zener on Vertical Socket.
b. VIF in tuning has not changed; Replace LA7555.
7. PHILLIPS-C14PT138J (Tvku dewe ...!)
Standby at the start protected; Check & Replace Vertical IC TDA3653B.
8. INTEL-IC1429N
Figure shrink both sides 3cm; Check C707 (100u 50V), D703 (1N5392).
9. PANASONIC-TC1450
a. Blanking & Protect; Replace AN5600.
b. No Sound; Check Q1112, 1113 (N4212) Replace with C114.
10. TOSHIBA-2840XH
Vertical defects (R, C, Elco, okay smua IC), check out Vertical Feedback drives = 3-4Volt.
Kerusakan2 Tv. (Sec. 4)
1. CONTEC KTB3731
Matrix (Color) chaotic, IC Video M51393 okay; Check R235 (8k2) broke!
2. NATIONAL (AN 5601)
At the start of life and die (Protect), Vcc okay; Check Q504 (Base must be 0 Volt)!
3. METZ 7401/3
Relay bissa on, B + no; Check R808 (2.2 Ohm ½ Watt), R821 (56 Ohm ¼ Watt)
4. LENS (KA2154, SMM105, KA2919)
Tuning okay, not memory; Check RR151 (150k) from AFT Tuner Pin 35 UCOM!
5. TAMASHI (TDA8362, SMP260WTC)
At the start Protect; Check TR Hor. Driver (C2482)?
6. SABA MF5222
a. Contrass not function, Voltage Swing okay; Check RL05 (100k) Pin 3-4 FBT!
b. Vertical defects above; Check CL15 (220u 16v).
c. Vertical mebuka 1cm below; Check CF06 (470n).
7. SABA MS3705
a. No OSD; Check R 68k in base amplifier RGB (Must be 4.8 volts)!
b. Blanking (No Snow); Cheque TR Video TV05 (BC558)?
8. SANSUI SV.M1460J
No sound, Voltage swing right; Replace TDA1013.
9. JVC C147LNS
Protect; Check M52016 and deflection.
10. DETRON / ETRON P1401
No Hor. Oscillator, Vcc okay; Replace TA 7698.
Kerusakan2 Tv. (Sec. 3)
1. OKAY 3732
Tv live, - / + 5 minutes off (Standby), Eeprom MN12C01 okay; Cheque Toll pathway
Validate (Ceramic 22N) leaked!
2. INDOTEC 2107
Vertical upper disability; Check R304 (56k) stretch!
3. AKAI CT14W9
a. Vertical does not open, AN5534 cold; Vertical Deflection part broke!
b. No snow, no OSD; 5v drop (5V1 Zener leak)!
4. DAEWOO DMQ1449M
Vertical defects, the top is white garis2; Replace LA7837!
5. Aetna C1420
a. Can not Standby (immediate start); Replace TMP87CK38N!
b. Blanking (Vcc okay); Replace TB1238AN!
c. Tuning slide, the sound of snoring (VIF does not function); Replace SAW Filter!
6. KONKA 1418C3
Pump up B +; Check Optic Coupler (PC817)!
7. RCA E14500 (SABA MT 3751)
a. B + Okay, Led Blink; Replace STV 2118!
b. No Sound Picture oke (Vcc TDA7253, Voltage Swing okay); Replace STV8224A!
c. Vertical up less 3cm; Adjust B +, must be 100V!
8. JOHNSONS CTV145AV
Standby can not start; Cheque Crystal IC Program!
9. CROWN T128
At the start snoring sound, either the account after 3 minutes (PIF okay); Replace Transformer SIF!
10. SEMRO TD1538
+ B can not be adjusted; Check R808 (10k) at the Regulator
Kerusakan2 Tv. (Sec. 2)
1. GOLDSTAR-C14D22
Stand By at the start protect LED flashing: Check Zener 6v8 in the bag. PSU.
If at the start led to death: Check SE110.
2. GOLDSTAR-CA14A95C
Manual tuning does not stop: Replace UCOM GS8334-02B.
3. SAMSUNG-CB3339Z
Blanking: Cheque supply 5v (7805).
4. SAMSUNG BIO-CB3366Z
Blanking (Vcc ok): Replace IC Chroma M52309SP.
5. SAMSUNG-CB2039Z
Tuning no channel (33V, VT okay): Checks 12v supply.
6. AIWA-C142KER
Vertical Line: Checks 12v supply.
7. SONY-KV1415GE
Tuning can not save channel: Replace UCOM M34302M8-712SP.
8. SOLYTRON-SM3725
Position AV voice channel remains: Check Q1006 to pin 12 IC 4053.
9. SOLYTRON-SM3792
Tuning can be stopped, but the channel is not trsimpan: Memory Check-30V supply.
10. SOLYTRON-SM3730
Sometimes it can start, sometimes die: Check 15V, C853 (4.7 u 50V NP).
Damage Tv. (Sec. 1)
1. DIGITEC DM-172 020
OSD not out: check T701, T712 (BC547).
BI-BIII okay, BU no: checks Band Switch LA7910.
2. DIGITEC DM-14 401
Tr.Hor dpasang B + drop: check C516 (1u50v).
3. DIGITEC-DM142014
Bright, Contrass not function: Checks T303 (BC557).
Horizontal not Syncron: Check T301 (BC548).
4. DIGITEC-DM2076
Contrass not function: open pin 25 TDA8361, TDA8361 Replace if ok.
5. DIGITEC-DM2142
Blue screen, No OSD: Replace TDA8361.
6. POLYTRON-GM1483
No OSD: open R723, D732.
7. AKARI-IC1439 R2N
No raster (Vcc ok): Check R411.
8. AKARI-IC1439RMD
B + drop, Heater no, Sound ok: Check C561, R443.
9. GOLDSTAR-SoundMAX
Color kadang2 missing: Check & Replace Ceramic pin 11 TDA8690.
10. GOLDSTAR-C14D22
No sound, no manual tuning stops: Check QO6 (C3198).
0 komentar:
Posting Komentar